How do I mount and level the 30oz Tapered Travel Tumbler in the xTool S1?

For the xTool S1: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 100mm diameter drinkware. 2) Insert the 30oz Tapered Travel Tumbler into the rotary fixture using Step 3 (85-115mm Jaw Position). 3) Adjust the leveling tilt angle to exactly 3.67° so the top rim and bottom base remain coplanar with the xTool S1's laser nozzle.

What diameter and steps-per-rotation do I enter in LightBurn for this pairing?

In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 12800 (or check $101=100). If engraving a small front logo, enter 87.50mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.

Will the 30oz Tapered Travel Tumbler clear the laser gantry or housing on the xTool S1?

The 30oz Tapered Travel Tumbler has a maximum outer diameter of 100mm and height of 195mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.

How do I focus the xTool S1 on the 30oz Tapered Travel Tumbler?

Focus the 50mm lens directly onto the apex (top tangent point) of the 30oz Tapered Travel Tumbler after leveling it by 3.67°. Use S1 pinpoint dual-point positioning system to capture tumbler top and bottom z-heights.

Laser: xTool S1 Blank: 30oz Tapered Travel Tumbler Tilt: 3.67° Ø 87.50mm

xTool S1 + 30oz Tapered Travel Tumbler Rotary Setup Guide

Engineered parameters for mounting and engraving the 30oz Tapered Travel Tumbler on the xTool S1. Configure chuck steps, rotary leveling tilt, and beam focus height below.

Tapered Tumbler Tilt-Angle & Conical Warp Tool

Active Blank: 30oz Tapered Travel Tumbler • Tumbler

Drinkware Blank Preset

1. Measured Blank Dimensions (Top, Base & Slant)Precision Caliper

Top Rim Outer Diameter

Circ: 314.2mm

Bottom Base Diameter

Circ: 235.6mm

Slant / Printable Height

Hypotenuse distance

2. Artwork Height & Seam AllowanceLogo Center: 50% from Top

Logo Height: 50mm

Vertical Placement: 50%

Include 2mm overlap seam allowance for full wrap sublimation or rotary masking

Conical Arc Template Preview • True Curvature

Cut Path Center Score

1:1 scale curved wrap SVG ready to import into LightBurn, XCS, Illustrator, or CAD.

Taper & Leveling TelemetryOPTICAL LEVELING

Mandatory Rotary Leveling Tilt Angle

3.67°tilt upwards

Tilt the rotary chuck or elevate the roller tailstock by 3.67°. This keeps the cup's outer engraving surface 100% parallel to the laser nozzle plane.

Effective Diameter at Logo Center (50% down)

87.5 mmenter in LightBurn

Enter this diameter in LightBurn Rotary Setup when engraving a single logo without full conical warping.

Circumference Distortion33.3%Top vs. Bottom

Conical Arc Angle23.03°Sector Span

Outer Arc Radius (R):781.6 mm

Inner Arc Radius (r):586.2 mm

Jig & Chuck Advice:

Tilt rotary assembly up by 3.7°. Support heavy base with live center tailstock to prevent cantilever wobble.

Recommended: Chuck with Tailstock SupportStep 3 (85-115mm Jaw Position)

Sponsored Hardware & ToolingAd Slot (min-h: 250px)

Monetization Slot: Native Under-Download Banner

High-CTR container positioned directly below the SVG export and rotary calculations. Configure your Adsterra native key in src/config/adsterra.ts.

xTool S1 • 30oz Tapered Travel Tumbler Mechanical Pairing Parameters

Setup Matrix

Target Laser Platform	xTool S1 (20W / 40W Diode, xTool Enclosed GRBL)
Target Drinkware Blank	30oz Tapered Travel Tumbler (Tumbler)
Recommended Rotary Fixture	Chuck with Tailstock Support
Recommended Chuck Jaw Step	Step 3 (85-115mm Jaw Position)
Rotary Leveling Tilt Angle	3.67°
Midpoint Average Diameter	87.50 mm (Circ: 274.9 mm)
Top Rim Circumference	314.16 mm (Full 360° Wrap)
Default Pulses / Rev	12800 pulses/rev
Focal Length & Alignment	50mm lens • Use S1 pinpoint dual-point positioning system to capture tumbler top and bottom z-heights.

Parent Machine Instrument

Need to calibrate the xTool S1 motor steps?

Open the dedicated xTool S1 SPR calibrator to burn a 20x100mm test ruler.

Open xTool S1 Calibrator →

Parent Drinkware Geometry

Need full conical wrap templates for 30oz Tapered Travel Tumbler?

View all 18 machine pairings, sector angles, and wrap generators for this blank.

Open 30oz Tapered Travel Tumbler Guide →

xTool S1 + 30oz Tapered Travel Tumbler Setup Technical FAQs

Q1: How do I mount and level the 30oz Tapered Travel Tumbler in the xTool S1?: For the xTool S1: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 100mm diameter drinkware. 2) Insert the 30oz Tapered Travel Tumbler into the rotary fixture using Step 3 (85-115mm Jaw Position). 3) Adjust the leveling tilt angle to exactly 3.67° so the top rim and bottom base remain coplanar with the xTool S1's laser nozzle.
Q2: What diameter and steps-per-rotation do I enter in LightBurn for this pairing?: In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 12800 (or check $101=100). If engraving a small front logo, enter 87.50mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.
Q3: Will the 30oz Tapered Travel Tumbler clear the laser gantry or housing on the xTool S1?: The 30oz Tapered Travel Tumbler has a maximum outer diameter of 100mm and height of 195mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.
Q4: How do I focus the xTool S1 on the 30oz Tapered Travel Tumbler?: Focus the 50mm lens directly onto the apex (top tangent point) of the 30oz Tapered Travel Tumbler after leveling it by 3.67°. Use S1 pinpoint dual-point positioning system to capture tumbler top and bottom z-heights.