xTool F1 Ultra + 30oz Tapered Travel Tumbler Rotary Setup Guide
Pre-configured engineering parameters for engraving the 30oz Tapered Travel Tumbler on the xTool F1 Ultra. Follow the pre-calculated chuck positions, tilt angle, and optical focus settings below.
Tapered Tumbler Rotary Tilt-Angle & Warp Template Generator
Preset: 30oz Tapered Travel Tumbler (Tumbler)
Tilt your rotary chuck or elevate the roller tailstock by exactly 3.67°. This guarantees the cup's outer engraving surface sits 100% parallel to the laser lens gantry throughout the rotation.
Enter this diameter in LightBurn's Rotary Setup when engraving an isolated logo without full conical warping.
Tilt rotary assembly up by 3.7°. Support heavy base with live center tailstock to prevent cantilever wobble.
Monetization Slot: Native Under-Download Banner
High-CTR placement positioned directly below the SVG export and rotary calculations. Configure your Adsterra native key in src/config/adsterra.ts.
xTool F1 Ultra • 30oz Tapered Travel Tumbler Pairing Parameters
Pre-Computed Settings| Target Machine | xTool F1 Ultra (20W Diode + 20W MOPA Fiber, Galvo DSP) |
|---|---|
| Target Drinkware Blank | 30oz Tapered Travel Tumbler (Tumbler) |
| Recommended Rotary Type | Chuck with Tailstock Support |
| Recommended Chuck Jaw Step | Step 3 (85-115mm Jaw Position) |
| Rotary Leveling Tilt Angle | 3.67° |
| Midpoint Average Diameter | 87.50 mm (Circ: 274.9 mm) |
| Top Rim Circumference | 314.16 mm (Full 360° Wrap) |
| Default Steps / Pulses Per Rev | 12800 pulses/rev |
| Focal Length & Alignment | 160mm lens • Overlap the red & blue dual laser pointer dots on the apex point of the blank. |
Need to verify the xTool F1 Ultra rotary steps-per-rotation?
Use the dedicated xTool F1 Ultra SPR calibrator to burn a 20x100mm test ruler.
xTool F1 Ultra + 30oz Tapered Travel Tumbler Setup FAQs
Q1: How do I mount and level the 30oz Tapered Travel Tumbler in the xTool F1 Ultra?
For the xTool F1 Ultra: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 100mm diameter drinkware. 2) Insert the 30oz Tapered Travel Tumbler into the rotary fixture using Step 3 (85-115mm Jaw Position). 3) Adjust the leveling tilt angle to exactly 3.67° so the top rim and bottom base remain coplanar with the xTool F1 Ultra's laser nozzle.
Q2: What diameter and steps-per-rotation do I enter in LightBurn for this pairing?
In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 12800 (or check $101=100). If engraving a small front logo, enter 87.50mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.
Q3: Will the 30oz Tapered Travel Tumbler clear the laser gantry or housing on the xTool F1 Ultra?
The 30oz Tapered Travel Tumbler has a maximum outer diameter of 100mm and height of 195mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.
Q4: How do I focus the xTool F1 Ultra on the 30oz Tapered Travel Tumbler?
Focus the 160mm lens directly onto the apex (top tangent point) of the 30oz Tapered Travel Tumbler after leveling it by 3.67°. Overlap the red & blue dual laser pointer dots on the apex point of the blank.