xTool S1 + 16oz Pint Glass / Beer Can Glass Rotary Setup Guide
Pre-configured engineering parameters for engraving the 16oz Pint Glass / Beer Can Glass on the xTool S1. Follow the pre-calculated chuck positions, tilt angle, and optical focus settings below.
Tapered Tumbler Rotary Tilt-Angle & Warp Template Generator
Preset: 16oz Pint Glass / Beer Can Glass (Glass)
Tilt your rotary chuck or elevate the roller tailstock by exactly 5.13°. This guarantees the cup's outer engraving surface sits 100% parallel to the laser lens gantry throughout the rotation.
Enter this diameter in LightBurn's Rotary Setup when engraving an isolated logo without full conical warping.
High 5.14° taper angle requires strong tilt leveling. Apply damp laser paper or dish soap coating to avoid micro-splinters.
Monetization Slot: Native Under-Download Banner
High-CTR placement positioned directly below the SVG export and rotary calculations. Configure your Adsterra native key in src/config/adsterra.ts.
xTool S1 • 16oz Pint Glass / Beer Can Glass Pairing Parameters
Pre-Computed Settings| Target Machine | xTool S1 (20W / 40W Diode, xTool Enclosed GRBL) |
|---|---|
| Target Drinkware Blank | 16oz Pint Glass / Beer Can Glass (Glass) |
| Recommended Rotary Type | Chuck with Rubber Padded Jaws |
| Recommended Chuck Jaw Step | Step 2 (Internal Rim Grip with Silicone Tape) |
| Rotary Leveling Tilt Angle | 5.14° |
| Midpoint Average Diameter | 75.00 mm (Circ: 235.6 mm) |
| Top Rim Circumference | 276.46 mm (Full 360° Wrap) |
| Default Steps / Pulses Per Rev | 12800 pulses/rev |
| Focal Length & Alignment | 50mm lens • Use S1 pinpoint dual-point positioning system to capture tumbler top and bottom z-heights. |
Need to verify the xTool S1 rotary steps-per-rotation?
Use the dedicated xTool S1 SPR calibrator to burn a 20x100mm test ruler.
xTool S1 + 16oz Pint Glass / Beer Can Glass Setup FAQs
Q1: How do I mount and level the 16oz Pint Glass / Beer Can Glass in the xTool S1?
For the xTool S1: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 88mm diameter drinkware. 2) Insert the 16oz Pint Glass / Beer Can Glass into the rotary fixture using Step 2 (Internal Rim Grip with Silicone Tape). 3) Adjust the leveling tilt angle to exactly 5.14° so the top rim and bottom base remain coplanar with the xTool S1's laser nozzle.
Q2: What diameter and steps-per-rotation do I enter in LightBurn for this pairing?
In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 12800 (or check $101=100). If engraving a small front logo, enter 75.00mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.
Q3: Will the 16oz Pint Glass / Beer Can Glass clear the laser gantry or housing on the xTool S1?
The 16oz Pint Glass / Beer Can Glass has a maximum outer diameter of 88mm and height of 145mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.
Q4: How do I focus the xTool S1 on the 16oz Pint Glass / Beer Can Glass?
Focus the 50mm lens directly onto the apex (top tangent point) of the 16oz Pint Glass / Beer Can Glass after leveling it by 5.14°. Use S1 pinpoint dual-point positioning system to capture tumbler top and bottom z-heights.