Creality Falcon2 Pro + 24oz Insulated Water Bottle Rotary Setup Guide
Pre-configured engineering parameters for engraving the 24oz Insulated Water Bottle on the Creality Falcon2 Pro. Follow the pre-calculated chuck positions, tilt angle, and optical focus settings below.
Tapered Tumbler Rotary Tilt-Angle & Warp Template Generator
Preset: 24oz Insulated Water Bottle (Bottle)
Tilt your rotary chuck or elevate the roller tailstock by exactly 0°. This guarantees the cup's outer engraving surface sits 100% parallel to the laser lens gantry throughout the rotation.
Enter this diameter in LightBurn's Rotary Setup when engraving an isolated logo without full conical warping.
Cylindrical body needs 0° tilt. Use rubber rings or tailstock support if narrow neck causes bottle skew.
Monetization Slot: Native Under-Download Banner
High-CTR placement positioned directly below the SVG export and rotary calculations. Configure your Adsterra native key in src/config/adsterra.ts.
Creality Falcon2 Pro • 24oz Insulated Water Bottle Pairing Parameters
Pre-Computed Settings| Target Machine | Creality Falcon2 Pro (22W / 40W Diode, GRBL 32-bit) |
|---|---|
| Target Drinkware Blank | 24oz Insulated Water Bottle (Bottle) |
| Recommended Rotary Type | Roller or Chuck |
| Recommended Chuck Jaw Step | Step 1 or 2 |
| Rotary Leveling Tilt Angle | 0° |
| Midpoint Average Diameter | 78.00 mm (Circ: 245.0 mm) |
| Top Rim Circumference | 245.04 mm (Full 360° Wrap) |
| Default Steps / Pulses Per Rev | 2560 pulses/rev |
| Focal Length & Alignment | 40mm lens • Use the multi-step focus block to seat focal bar precisely 40mm above cup rim apex. |
Need to verify the Creality Falcon2 Pro rotary steps-per-rotation?
Use the dedicated Creality Falcon2 Pro SPR calibrator to burn a 20x100mm test ruler.
Creality Falcon2 Pro + 24oz Insulated Water Bottle Setup FAQs
Q1: How do I mount and level the 24oz Insulated Water Bottle in the Creality Falcon2 Pro?
For the Creality Falcon2 Pro: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 78mm diameter drinkware. 2) Insert the 24oz Insulated Water Bottle into the rotary fixture using Step 1 or 2. 3) Adjust the leveling tilt angle to exactly 0° so the top rim and bottom base remain coplanar with the Creality Falcon2 Pro's laser nozzle.
Q2: What diameter and steps-per-rotation do I enter in LightBurn for this pairing?
In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 2560 (or check $101=80). If engraving a small front logo, enter 78.00mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.
Q3: Will the 24oz Insulated Water Bottle clear the laser gantry or housing on the Creality Falcon2 Pro?
The 24oz Insulated Water Bottle has a maximum outer diameter of 78mm and height of 190mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.
Q4: How do I focus the Creality Falcon2 Pro on the 24oz Insulated Water Bottle?
Focus the 40mm lens directly onto the apex (top tangent point) of the 24oz Insulated Water Bottle after leveling it by 0°. Use the multi-step focus block to seat focal bar precisely 40mm above cup rim apex.