Creality Falcon2 Pro + 40oz Quencher Tumbler — Lower Base Rotary Setup Guide
Pre-configured engineering parameters for engraving the 40oz Quencher Tumbler — Lower Base on the Creality Falcon2 Pro. Follow the pre-calculated chuck positions, tilt angle, and optical focus settings below.
Tapered Tumbler Rotary Tilt-Angle & Warp Template Generator
Preset: 40oz Quencher Tumbler — Lower Base (Tumbler)
Tilt your rotary chuck or elevate the roller tailstock by exactly 1.3°. This guarantees the cup's outer engraving surface sits 100% parallel to the laser lens gantry throughout the rotation.
Enter this diameter in LightBurn's Rotary Setup when engraving an isolated logo without full conical warping.
Tilt rotary 1.30° when engraving lower cup-holder section. Ensure clearance for overhang shoulder above.
Monetization Slot: Native Under-Download Banner
High-CTR placement positioned directly below the SVG export and rotary calculations. Configure your Adsterra native key in src/config/adsterra.ts.
Creality Falcon2 Pro • 40oz Quencher Tumbler — Lower Base Pairing Parameters
Pre-Computed Settings| Target Machine | Creality Falcon2 Pro (22W / 40W Diode, GRBL 32-bit) |
|---|---|
| Target Drinkware Blank | 40oz Quencher Tumbler — Lower Base (Tumbler) |
| Recommended Rotary Type | Chuck (External Clamping on Base) |
| Recommended Chuck Jaw Step | Step 1 or 2 |
| Rotary Leveling Tilt Angle | 1.3° |
| Midpoint Average Diameter | 74.00 mm (Circ: 232.5 mm) |
| Top Rim Circumference | 238.76 mm (Full 360° Wrap) |
| Default Steps / Pulses Per Rev | 2560 pulses/rev |
| Focal Length & Alignment | 40mm lens • Use the multi-step focus block to seat focal bar precisely 40mm above cup rim apex. |
Need to verify the Creality Falcon2 Pro rotary steps-per-rotation?
Use the dedicated Creality Falcon2 Pro SPR calibrator to burn a 20x100mm test ruler.
Creality Falcon2 Pro + 40oz Quencher Tumbler — Lower Base Setup FAQs
Q1: How do I mount and level the 40oz Quencher Tumbler — Lower Base in the Creality Falcon2 Pro?
For the Creality Falcon2 Pro: 1) Ensure any necessary riser base or honeycomb removal is completed to allow clearance for 76mm diameter drinkware. 2) Insert the 40oz Quencher Tumbler — Lower Base into the rotary fixture using Step 1 or 2. 3) Adjust the leveling tilt angle to exactly 1.3° so the top rim and bottom base remain coplanar with the Creality Falcon2 Pro's laser nozzle.
Q2: What diameter and steps-per-rotation do I enter in LightBurn for this pairing?
In LightBurn Tools > Rotary Setup: Set steps-per-rotation to 2560 (or check $101=80). If engraving a small front logo, enter 74.00mm into the cylinder diameter field. If wrapping a 360° graphic, use our downloadable SVG generator for true conical warp.
Q3: Will the 40oz Quencher Tumbler — Lower Base clear the laser gantry or housing on the Creality Falcon2 Pro?
The 40oz Quencher Tumbler — Lower Base has a maximum outer diameter of 76mm and height of 88mm. Verify that any handle or mug curve clears the laser nozzle during a 360° dry framing run before firing the laser.
Q4: How do I focus the Creality Falcon2 Pro on the 40oz Quencher Tumbler — Lower Base?
Focus the 40mm lens directly onto the apex (top tangent point) of the 40oz Quencher Tumbler — Lower Base after leveling it by 1.3°. Use the multi-step focus block to seat focal bar precisely 40mm above cup rim apex.